You are here

EZ-PD™ CCG2 Automotive USB Type-C and Power Delivery Controller | サイプレス セミコンダクタ

EZ-PD™ CCG2 Automotive USB Type-C and Power Delivery Controller


ModusToolbox™ was built to make the developers life easy. It is a collection of easy-to-use software and tools enabling rapid development of Infineon MCUs, covering applications from embedded sense...
PSoC ソフトウェア
サイプレスは高性能の埋め込みシステム設計のためのワンストップ・ショップです。We back up our uniquely flexible programmable system-on-chip architectures with high quality software tools that help you...
Cypress' Wi-Fi, 802.15.4 and Bluetooth® technology products, enable cost-effective, low-power, short or long range wireless connectivity solutions for the Internet of Things.
Cypress develops and markets general-purpose and application-specific 8-, 16- and 32-bit controllers for a wide range of consumer, automotive, industrial, medical and other applications.
パワー マネージメント
Bluetooth low energy
PSoC 4 BLE and PRoC BLE devices support new Bluetooth Smart 4.2 features including Data-Length Extension (800Kbps), Lower-Power Privacy, and Enhanced Security.
産業および車載向けに幅広いメモリ ソリューションを提供します。

EZ-PD CCG2 Automotive is Cypress’ first AECQ-100 USB Type-C controller that complies with the USB Type-C and PD 2.0 standards. EZ-PD CCG2 Automotive provides a complete solution for in-vehicle charger ports and integrates a Type-C Transceiver, termination resistors and system level ESD. EZ-PD CCG2 Automotive controller is certified by the USB Implementers Forum (USB-IF). CCG2 has an Arm® Cortex®-M0 with 32KB flash to enable firmware upgrades anytime, anywhere—during product development, on the production line or in the field.

EZ-PD CCG2 Automotive Product Features

  • 32-bit MCU Subsystem
    • 48-MHz Arm® Cortex® -M0 Processor
    • 32KB Flash and 4KB SRAM
  • USB 3.1 Type-C Support
    • Integrated transceiver, supporting one Type-C port
  • PD 2.0 Support
    • Standard power profiles
  • Integrated Digital Blocks
    • Integrated timers, counters and pulse-width modulators
    • Two Serial Communication Blocks (SCB) configurable to I2C, SPI or UART modes
    • Up to 14 GPIOs (QFN)
  • Low-Power Operation
    • Two independent VCONN rails with integrated isolation
    • Independent supply voltage pin for GPIO
    • 2.7-V to 5.5-V operation
    • Sleep: 2.0 mA; Deep Sleep: 2.5 μA; Reset: 1.0μA
  • System-Level ESD on CC and VCONN Pins
    • ±8-kV contact, ±15-kV Air Discharge IEC61000-4-2 level 4C
  • Packages
    • 24-pin QFN (16mm2)
  1. Watch the Type-C 101 Video Series
  2. Download the CCG2 Automotive Datasheet
  3. Order the CY4502 EZ-PD™ CCG2 Development Kit
  4. Refer to the Type-C Reference Designs page
  5. Refer to CCGx FAQ page
  6. Get your Schematics reviewed by the Cypress Applications Engineering Team using the Online Tech Support Case System
    CY4521 EZ-PD™ CCG2 Evaluation Kit


    EZ-PD™ CCG2 Evaluation Kit

    The CY4521 EZ-PD CCG2 Evaluation Kit is used to emulate a USB Type-C Host system. This kit features a Type-C host board along with a CCG2 daughter card.

    CY4500 EZ-PD™ Protocol Analyzer


    EZ-PD™ Protocol Analyzer

    The CY4500 EZ-PD™ Protocol Analyzer records traffic passively on the Configuration Channel (CC) and allows user to analyze and debug USB Power Delivery communication.

    USB Type-C Specification

    USB Type-C is the new USB-IF standard that solves several challenges faced by today's Type-A and Type-B cables and connectors. USB Type-C uses a slimmer connector (measuring only 2.4-mm in height) to allow for increasing miniaturization of consumer and industrial products. The specification allows for fully reversible plugs and enables transport of both USB signals and PCIe or DisplayPort signals on the same connector. The Type-C specification aslo increases the power delivery capability from 7.5 W to 100 W.